25 Aug Commonwealth Drive, Warrendale, PA SURFACE VEHICLE STANDARDSTA NDARD J REV. DEC83 1 Dec Buy SAE J Hardness Tests And Hardness Number Conversions from SAI Global. SAE J Hardness Tests And Hardness Number Conversions. Be notified when this Standard is updated or amended – Add to StandardsWatch. General.

Author: Kicage Mikarisar
Country: Sri Lanka
Language: English (Spanish)
Genre: Automotive
Published (Last): 8 February 2007
Pages: 437
PDF File Size: 6.59 Mb
ePub File Size: 9.57 Mb
ISBN: 917-3-59306-403-7
Downloads: 57909
Price: Free* [*Free Regsitration Required]
Uploader: Kazigar

This standard specifies the units of force xae length in sae j417 International System of Units SI ; that is, force in Newtons Sae j417 and length in millimeters mm. Sae j417 Version saae – view sae j417 versions of standard. Where more precise conversions are required, they should be developed specially for each steel composition, heat treatment, and part. This standard provides the requirements for Rockwell hardness machines and the procedures for performing Rockwell hardness tests.

However, because of the historical precedent and continued common usage, force values in kgf units and ball diameters in inch units are provided for information and much of the discussion in this standard refers to these units.

It is impossible to give exact relationships because of the inevitable influence of size, mass, composition, and method of sae j417 treatment. Link to Active This link will always route to the current Active version of the standard.

— Page Not Found

Standardization of Rockwell Indenters. New sae j417 AWS C1. This information may correlate to tensile strength, wear resistance, ductility, and other physical characteristics of metallic materials, and may be useful in quality control and selection of materials.

This report lists approximate hardness conversion values; test methods for Vickers Hardness, Brinell Hardness, Sae j417 Hardness Rockwell Superficial Hardness, Shore Hardness; and information regarding surface preparation, specimen thickness, effect of curved surfaces, and recommendations for Sae j417 surface hardness testing for case hardened parts.

The same type and size indenters may be used for either test, depending on the scale being employed.

The significant differences between the two tests are that the test forces are smaller for the Sae j417 superficial test than for the Rockwell test. Cart products product empty. The tables in this report give the approximate relationship of Vickers Brinell, Rockwell, and Scleroscope hardness values and sae j417 approximate tensile strengths of steels.

Welcome, Log in Your Account Cart: Sae j417, throughout this standard, the term Rockwell will imply both Rockwell and Rockwell superficial unless stated otherwise.

Work Item s – proposed revisions of this standard. Rockwell Hardness Standardizing Machines.

It is the responsibility of the user of this standard to establish appropriate safety and health sae j417 and determine the applicability of regulatory limitations prior to use. Specials NAS Rev. The accompanying conversion tables for steel hardness numbers are based 4j17 extensive tests on carbon and alloy steels, mostly in the heat treated condition, but sae j417 been found to be sae j417 on practically all constructional alloy steels and tool steels in the as-forged, annealed, normalized, and saee and tempered conditions, provided they are homogeneous.

ASTM E18 – 17e1 Standard Test Methods for Rockwell Hardness of Metallic Materials

Sae j417 of Rockwell Hardness Testing Machines. All numbers in these tables given in bold face type were prepared jointly by the Sae j417 Society for Testing and Materials, the American Society for Metals, and SAE from carefully checked data. Standardization of Rockwell Hardness Test Blocks.

Currency Dollar Euro Pound. sea

Referenced Documents purchase separately The documents listed below sae j417 referenced within the subject standard but are not provided as part of the standard.