9 May SikaGrout® 1. 1/4. C onstruction. SikaGrout® SikaGrout® High Strength shrinkage compensated cementitious grout. Product. Specialist Construction Supplies for Repair, Maintenance, Building & Infrastructure. Sikagrout Data Sheet. Specification notes. Product: Sikagrout SikaGrout DIVISION 3 – CONCRETE. Section – Grouts. Part 1 – General. Summary. A. This specification describes the grouting of cavities, voids.
|Published (Last):||6 March 2018|
|PDF File Size:||2.36 Mb|
|ePub File Size:||15.22 Mb|
|Price:||Free* [*Free Regsitration Required]|
Ensure that sikagrout 212 grout is available to maintain the hydrostatic pressure throughout the grouting operation until the grout level is above the bottom level of the base plate. Add the required amount of water to the mixing vessel and then add Sika Grout Remove uncured Sika Grout from tools and equipment with water. Dispose of in accordance with local regulations. sikagrout 212
Cured material can only be removed mechanically. Wash thoroughly sikagrout 212 soap and water. Users should always refer to the most recent issue of the Technical Data Sheet for the product concerned, copies of which sikagrout 212 be supplied on request, or can be accessed on the internet under www. Sika Grout can be used to fill voids up sikarout mm in depth.
A slight agitation of the sikatrout will assist sikagrout 212 Sika Grout to fill the annulus evenly. Mixing can be achieved either manually or mechanically. Contains Portland cement sikagrotu crystalline free silica. Use of an approved sikagrout 212 respirator, safety goggles and chemical resistant gloves are recommended. The quantity of sikagrout 212 added should not exceed one 1 part of aggregate to one 1 part sikagrout 212 Sika Grout by weight. Mix for at least 3 minutes until a uniform, lump-free consistency is obtained.
The use of standard concrete curing techniques, such as light water fogging for 72 hours or the application of a suitable water based curing compound is recommended on all exposed surfaces of Sika Grout Protect from direct sunlight.
Contact Sika for further health and safety information. In practice, the differences in materials, substrates and actual site conditions are such that no warranty in respect of merchantability or of fitness for a particular purpose, nor any liability arising out of any legal relationship whatsoever, can be inferred either sikagrout 212 this information, or from any written recommendations, or from any other advice offered.
Wash hands immediately after use. All orders sikagrout 212 accepted subject to our current terms of sale and delivery which are available on request. All surfaces sikagrout 212 be brought to a saturated surface dry condition by presoaking with clean water for several hours before grouting. The correct quantity of Sika Grout required to completely fill the annular gap between the bolt and the sides of the hole sikagrout 212 be determined before installation is attempted.
For the structural grouting of: Water Requirement per 25 kg bag in litres. Immediately remove contaminated clothing. If the Sika Sikagrout 212 does not fill the annular gap evenly during bolt sikagrout 212, withdraw the bolt and insert additional Sika Grout and re-insert the bolt.
SikaGrout – Everbuild
Remove affected sikagrout 212 to fresh air immediately and contact a physician. Sika Grout is a one component, multi-purpose,freeflowing, expanding,cementitious grout.
Machine base plates Column base sikagrout 212 Bearing plates Precast wall panels Crane rails Anchor bolts Concrete repairs where grout consistencies ranging from free flowing to dry packing are required. Water Requirements for Skagrout Wash clothing before re-use.
In most cases, the bolt hole should be no greater than 15 mm larger in diameter than the bolt. Approximate Flow Sikagrout 212 in cm. DO not attempt to sikarout additional Sika Grout with the bolt in place.
After establishing the sikabrout required, determine the water requirement per 25 kg bag see Sikagrout 212 2. Do not commence fogging until initial set has been reached.
The expansive properties of Sika Grout will be severely slkagrout if heat is introduced to the mixed product via warm batching water, sikagrout 212 storage conditions of Sika Groutand high substrate and ambient temperatures. The Company reserves itself the right to change the formulation of Sika products if so sikagrout 212 by new research and development.
Collect in appropriate container. Place Sika Grout within 30 minutes of mixing.